ConcreteCalculatorHQ

How to Build a Gravel Driveway

A gravel driveway is three layers of stone on a compacted, crowned base. Get the base and drainage right and the top stays put.

By Marcus Delgado, concrete estimator · Updated October 2026

Quick answerStrip 8–12 inches of sod and topsoil and compact the soil. Lay geotextile fabric, then build three compacted layers: 4–6 in of #3 or #4 stone, about 4 in of #57, and 2–3 in of crusher run on top. Crown the surface ½ inch per foot so water runs off. Budget $1–$2 per sq ft to resurface and $4–$10 per sq ft for a new full-depth build.
8–12 in
Dig depth (more on clay)
3 layers
Base, middle, top
½ in / ft
Crown from center to edge
$4–$10
Per sq ft, new full-depth build

How much gravel do I need?

Enter the driveway size. Change any layer depth to match your plan. You get tons for each layer, truckloads, fabric, and a stone budget.

Order about
66.7tons of stone

≈ 4.4 tandem truckloads · about $2,669 in stone · 147 sq yd of fabric (10% overlap).

Crusher run · 3 in22.7 t
#57 stone · 4 in22 t
#3 stone · 4 in22 t
Geotextile fabric on compacted soil

Uses 1.35 tons per cubic yard for #3 and #57 stone and 1.86 for compacted crusher run, plus 10% extra per layer. Truckloads assume a 15-ton tandem. Need one material at a time? Try the crusher run or #57 stone calculator.

Newly built gray gravel driveway curving toward a farmhouse with a crowned center, a grassy drainage ditch, and a plate compactor
Crowned center, crisp edges, and a ditch to carry the water away: the three things that keep a gravel driveway from rutting.

Step by step

  1. 1
    Call 811 and check permits
    Call 811 a few days before digging so buried utility lines get marked. Ask your county or town road department about permits, especially where the driveway meets a public road. Many require a culvert there, often 15–18 inches minimum.
  2. 2
    Mark the layout
    Stake both edges and run string lines. Plan 10–12 ft wide for one car, about 20 ft for two side by side. Keep curves gentle enough for a delivery truck.
  3. 3
    Dig out the topsoil
    Strip all sod and topsoil: 8–12 inches is typical (6–8 on firm soil for cars, 12–18 on soft clay). Shape the bottom with the same crown as the finished surface and compact it.
  4. 4
    Roll out geotextile fabric
    On clay or soft soil, lay woven driveway fabric over the compacted subgrade and overlap the seams 12–18 inches. It keeps the stone from sinking into the mud.
  5. 5
    Base layer: 4–6 in of #3 or #4 stone
    Spread big base stone in 3–4 inch layers and compact each one with a plate compactor or roller. This layer carries the load.
  6. 6
    Middle layer: about 4 in of #57
    Clean #57 stone locks into the base and lets water drain through. Spread it evenly and compact.
  7. 7
    Top layer: 2–3 in of crusher run
    Finish with stone that has fines: crusher run, #411, or your area's road base. Dampen it, compact it, and shape a crown that drops about ½ inch per foot (4%) from the center to each edge.
  8. 8
    Edges and drainage
    Add edging where the driveway meets lawn or beds, and a shallow ditch or swale on the uphill side. Water standing on or beside a gravel driveway is what ruins it.

Crown and drainage

Crown: water must run off, not soak in
3 in higherRain runs to both edgesDitchDitch12 ft wide · ½ in drop per foot (4%)

FHWA recommends about ½ inch per foot (4%) and no more than 6%. Penn State uses ½–¾ inch per foot. A flat gravel driveway holds puddles and potholes within a season.

On a long driveway, the side ditches need somewhere to go. Run them to a low spot, a culvert under the driveway, or a daylighted outlet. Where the driveway crosses a roadside ditch, most road departments require a culvert pipe.

Which gravel goes where

Driveway stone by layer
StoneSizeLayerWhy
#3 or #42–1 in / 1½–¾ inBaseBig stone spreads the load over soft soil
#571 in to 3/16 inMiddleLocks into the base and drains
Crusher run / #4111–1½ in to dustTopFines bind into a hard, smooth surface
#8 (10 mm)3/8 inTop (light use only)Smooth to walk on but shifts without fines
Pea gravel3/8 in, roundNot recommendedRolls under tires and ruts

FHWA's surface-gravel spec calls for fines in the top layer so it binds. UK sizes: 10 mm ≈ 3/8 in, 20 mm ≈ 3/4 in.

Do
  • Strip sod and topsoil to firm soil
  • Compact each layer separately
  • Use fabric on clay or wet ground
  • Crown the top about ½ in per foot
  • Use angular stone with fines on top
Don't
  • Dump gravel straight on grass
  • Spread 12 inches in one pass
  • Use pea gravel or river rock on top
  • Leave the surface flat
  • Skip the 811 call

What a gravel driveway costs

2026 cost ranges
ItemCost
Resurfacing over an existing base$1.25–$1.80 per sq ft
Installed, typical range$1–$10 per sq ft (average about $1,800)
New full-depth build$4–$10 per sq ft
DIY: materials and equipment$800–$2,500
Hiring a pro$1,500–$6,000
Plate compactor rentalAbout $89 per day
Grading$1–$3 per sq ft
Culvert$500–$2,000
Edging$5–$18 per linear ft
Permit$50–$300

Bob Vila, Angi, and HomeGuide 2026; compactor rental from a Cleveland rental yard. The wide installed range is because a top-up and a new build are different jobs.

Installed cost by driveway size (Angi 2026)
Driveway sizeInstalled cost
200–300 sq ft$250–$900
400–600 sq ft (about 20×20 to 20×30)$800–$2,200
1,000+ sq ft$1,000–$5,000
2,000 sq ft$3,500–$6,000+

Keeping it in shape

Every car kicks a little stone off. The FHWA rule of thumb: about 1 ton of gravel lost per mile per year for each vehicle per day. A 300 ft driveway with 10 trips a day loses about half a ton a year, so plan a small top-up every year or two.

  • Rake or drag the surface each spring to fill ruts and restore the crown.
  • Patch potholes with crusher run, tamped in, never with pea gravel.
  • Clear leaves and silt out of the side ditches and culvert ends.
  • Pull weeds early; they trap silt and soften the surface.
Indy Farm Life builds one from bare ground: excavation, fabric, base stone, and top coat.

Frequently asked questions

How deep do you dig for a gravel driveway?

Usually 8–12 inches. On firm, well-drained soil for cars only, 6–8 inches can work. On soft clay or where heavy trucks will drive, dig 12–18 inches and use fabric.

How much does a 20x20 gravel driveway cost?

A 400 sq ft driveway built with our three default layers takes about 22 tons of stone, roughly $550–$1,100 at $25–$50 a ton before delivery. Angi's 2026 installed range for 400–600 sq ft is $800–$2,200.

Is a gravel driveway cheaper than concrete?

Yes, by a lot. Gravel runs about $1–$10 per sq ft depending on how much base work is needed, while a plain poured concrete slab runs roughly $6.50–$10.50 per sq ft. Gravel needs more upkeep over the years.

Do I need a permit for a gravel driveway?

Often, if it connects to a public road, needs a culvert, or changes how water drains. Permits typically cost $50–$300. Call your county road department or town hall before you dig, and check HOA rules.

Should I use 10mm or 20mm gravel?

Those are UK sizes. 10 mm is about 3/8 inch (#8 stone) and 20 mm is about 3/4 inch (#57 or #67). In the US, use #57 for the middle layer and crusher run or another stone with fines on top. Small round gravel on its own will rut.

Can you put gravel over grass?

Not if you want it to last. Grass and topsoil rot and compress under the stone, so the driveway sinks and ruts. Strip the sod and topsoil down to firm subsoil first.

Why shouldn't I use pea gravel for a driveway?

Pea gravel is round, so it rolls under tires like ball bearings, ruts, and scatters into the lawn. Driveway surfaces need angular stone with fines that lock together when compacted.

How long does a gravel driveway last?

With regular regrading and top-ups, 10–20 years for the surface, and a well-drained base much longer. Neglected drainage is the usual reason a gravel driveway fails early.

Related calculators

Sources we checked