ConcreteCalculatorHQ

Limestone Calculator

Pick the limestone product, enter your area and depth, and see the tons and cubic yards to order.

Your measurements

Area shape

After compaction, not before.

Material & extra allowance

Use supplier density for the matching material state. Defaults are planning assumptions.

Price & delivery

USD. No assumed prices, taxes, labor, or supplier minimums.

Truckloads & coverage
Crushed limestone layerNot to scale
20 ft x 10 ft / 4 in
Plan to order
3.36US tons

Includes 5% extra.

Finished depth: 4 in. Finished density: 96 lb/ft³. Loose delivery density: 96 lb/ft³.

Area
200 sq ft
Loose delivery estimate
2.59 yd³
Finished volume before extra
2.47 yd³
Truckloads at 18 US tons/load
1 load
The calculation

200 sq ft × 4 in = 2.469 yd³ before extra.

With 5% extra: 2.593 yd³ in the finished state.

At 96 lb/ft³: 3.36 US tons.

Same mass ÷ loose density (96 lb/ft³) = 2.593 yd³ for delivery.

Quantity estimate only. Confirm density, product suitability, order size, and delivery fees with your supplier.

Limestone products and their weights

Pile of light gray crushed limestone with a steel shovel in it at a stone yard
Crushed limestone is lighter in color than granite and softer. Its dust is pale gray to off-white.
Tons per cubic yard of crushed limestone
  • #57 / #8 limestone≈ 1.30
  • #411 / crusher run, loose≈ 1.35
  • Screenings, compacted≈ 1.53
  • #411 / crusher run, compacted≈ 1.86

Vulcan Materials limestone densities: coarse 96, screenings 113, crusher run 138 lb/ft³. Loose crusher run per FEMA appeal 1930-DR-IA.

Common limestone products
ProductSizeUse it for
#57 limestone1 in to 3/16 in, no dustDrainage, under slabs, driveway middle layer
#8 limestone3/8 inPaver joints, decorative paths, small drainage
#411 / quarry process#57 plus limestone dustDriveways and bases that need to pack hard
Screenings (lime dust)3/16 in to dustLeveling, fine top-dressing on paths
#3 / #4 limestone2 in to 3/4 inDriveway base over soft ground

#411 is a regional name (Ohio, Pennsylvania, Maryland, Virginia). Gradations vary by quarry.

Don't use solid-rock weight

Some limestone calculators default to the density of solid limestone. A pile of crushed stone is roughly a third air, so that overstates the tons by about 50%. This calculator uses bulk densities for crushed product.

Ohio's Kokosing quarry publishes higher "ordering factors": 1.5 tons per yard for fine material, 1.65 for coarse stone (#57, #8), and 1.75 for base (304, 411, screenings). Those build in a margin. If your quarry quotes a factor like that, enter it as the density (1 ton per yard = 74 lb/ft³) so your order matches theirs.

Limestone cost

HomeGuide's 2026 national range for crushed limestone is $30–$38 per ton, or $35–$54 per cubic yard delivered. #411 (quarry process) is usually the cheapest limestone product because it's sold as it comes off the crusher. Bagged limestone at hardware stores runs $3–$5 a bag, which works out to roughly $125 a ton.

Crusher run vs clean ¾-inch limestone: how they look, pack, and drain.

How to use this calculator

  1. 1. Enter measurements
    Choose the area shape and enter its dimensions.
  2. 2. Enter depth
    Use the finished depth specified for your project.
  3. 3. Review the estimate
    Confirm the quantity and order details with your supplier.

Quick checks

Use supplier data
Replace the default density and price when you have a quote.
Check the order
Allow for site waste and supplier minimums before buying.